poky: dylan adb63ca02348af72a30cef2f20de2234b74a7200 image download from http://autobuilder.yoctoproject.org/pub/nightly/20130410-1 core image use: core-image-sato-sdk-beagleboard-20130410221122.rootfs.tar.bz2 The X server could not start. This is a regression issue than 20130403 edition. Set boot env as below to print some debug info: setenv bootcmd 'mmc rescan 0; fatload mmc 0:1 0x80300000 uImage; bootm 0x80300000' setenv bootargs 'console=tty0 console=ttyO2,115200n8 root=/dev/mmcblk0p2 rootwait rootfstype=ext3 ro' boot The serial output: Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 gadget: Mass Storage Function, version: 2009/09/11 gadget: Number of LUNs=1 lun0: LUN: removable file: (no medium) gadget: Mass Storage Gadget, version: 2009/09/11 gadget: userspace failed to provide iSerialNumber gadget: g_mass_storage ready musb-hdrc musb-hdrc: MUSB HDRC host driver musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice twl_rtc twl_rtc: Power up reset detected. twl_rtc twl_rtc: Enabling TWL-RTC twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 cpuidle: using governor ladder cpuidle: using governor menu usb 1-2: new high-speed USB device number 2 using ehci-omap usbcore: registered new interface driver usbhid usbhid: USB HID core driver OMAP3 Beagle/Devkit8000 SoC init soc-audio soc-audio: ASoC machine omap3beagle should use snd_soc_register_card() twl4030-codec twl4030-codec: ASoC: Failed to create Capture debugfs file asoc: twl4030-hifi <-> omap-mcbsp.2 mapping ok oprofile: hardware counters not available oprofile: using timer interrupt. pktgen: Packet Generator for packet performance testing. Version: 2.74 NET: Registered protocol family 15 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. sr_init: No PMIC hook to init smartreflex smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized SmartReflex Class3 initialized clock: disabling unused clocks to save power hub 1-2:1.0: USB hub found hub 1-2:1.0: 5 ports detected Console: switching to colour frame buffer device 210x65 omapdss DPI: Could not find exact pixel clock. Requested 146262 kHz, got 144000 kHz VDAC: incomplete constraints, leaving on twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) ALSA device list: #0: omap3beagle Waiting for root device /dev/mmcblk0p2... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 1234 mmcblk0: mmc0:1234 SA04G 3.63 GiB mmcblk0: p1 p2 EXT3-fs (mmcblk0p2): recovery required on readonly filesystem EXT3-fs (mmcblk0p2): write access will be enabled during recovery usb 1-2.1: new high-speed USB device number 3 using ehci-omap smsc95xx v1.0.4 smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, f2:1a:16:78:5d:07 usb 1-2.2: new high-speed USB device number 4 using ehci-omap hub 1-2.2:1.0: USB hub found hub 1-2.2:1.0: 7 ports detected usb 1-2.2.5: new low-speed USB device number 5 using ehci-omap input: Dell Dell USB Keyboard as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-2/1-2.2/1-2.2.5/1-2.2.5:1.0/input/input0 generic-usb 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-ehci-omap.0-2.2.5/input0 usb 1-2.2.6: new low-speed USB device number 6 using ehci-omap input: USB Optical Mouse as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-2/1-2.2/1-2.2.6/1-2.2.6:1.0/input/input1 generic-usb 0003:0461:4D15.0002: input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-ehci-omap.0-2.2.6/input0 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 179:2. devtmpfs: mounted Freeing init memory: 244K INIT: version 2.88 booting mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Starting udev udevd[96]: error getting socket: Address family not supported by protocol error initializing udev control socketudevd[96]: error initializing udev control socket error getting socket: Address family not supported by protocol udevadm[97]: error getting socket: Address family not supported by protocol error getting socket: Address family not supported by protocol udevadm[99]: error getting socket: Address family not supported by protocol Starting Bootlog daemon: bootlogd. EXT3-fs (mmcblk0p2): using internal journal ALSA: Restoring mixer settings... Configuring network interfaces... Found hardware: "omap3beagle" "" "" "" "" Hardware is initialized using a generic method ifconfig: socket: Address family not supported by protocol ifconfig: socket: Address family not supported by protocol Starting rpcbind daemon...rpcbind: cannot create socket for local rpcbind: cannot create socket for udp rpcbind: cannot create socket for tcp rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 done. Wed Apr 10 23:32:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: Failed to start message bus: Failed to open socket: Address family not supported by protocol Starting Connection Manager Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting advanced power management daemon: apmd. apmd[223]: apmd 3.2.1 interfacing with apm driver 1.13 and APM BIOS 1.2
udevd[96]: error getting socket: Address family not supported by protocol udevadm[97]: error getting socket: Address family not supported by protocol udevadm[99]: error getting socket: Address family not supported by protocol ifconfig: socket: Address family not supported by protocol ifconfig: socket: Address family not supported by protocol rpcbind: cannot create socket for local rpcbind: cannot create socket for udp rpcbind: cannot create socket for tcp rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 Failed to start message bus: Failed to open socket: Address family not supported by protocol Networking is well and truly missing in this build.
Its possible the kernel config was corrupted by http://git.yoctoproject.org/cgit.cgi/poky/commit/?id=4c02dd5f6432c6e683a57d47b610f56433e9ca0d
Bruce, there was ARM kernel breakage that you just fixed: would that be the cause of this and therefore it's resolved in git?
It is worth a re-test. The combination of that kern-tools fix + the KERNEL_EXTRA_FEATURES only being applied to qemux86* would mean that netfilter and other useful options were being dropped. I've upreved the beagleboard to 3.8 here, and networking works, so this is worth a retest on 3.4 now.
Ok, marking as needinfo. Ning Zhang, please re-test.
(In reply to comment #5) > Ok, marking as needinfo. Ning Zhang, please re-test. Hi, i retested it on 20130411-3 images. It has the same issue. Still "Failed to open socket" Poky: poky dylan dab237bc6a7679dfeaa981c14736aedc7b04ecb9 Download image from: http://autobuilder.yoctoproject.org/pub/nightly/20130411-3/machines/beagleboard/ I used below bootfiles: core-image-sato-sdk-beagleboard-20130411161536.rootfs.tar.bz2 MLO-beagleboard-1.5.0+gitAUTOINC+9f94c6577e3a018b6b75cbe39f32bb331871f915-r0 u-boot-beagleboard-v2011.06+gitAUTOINC+b1af6f532e0d348b153d5c148369229d24af361a-r3.bin uImage--3.4.36+gitAUTOINC+80b4b5110dca5184b57e85f1e775fb006a2e85ad_c994390cfa28339cbc1ec3b56eeec83a5fa75bb7-r4.3-beagleboard-20130411161536.bin Test Log: Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. musb-hdrc: version 6.0, ?dma?, otg (peripheral+host) musb-hdrc musb-hdrc: USB OTG mode controller at fa0ab000 using DMA, IRQ 92 gadget: Mass Storage Function, version: 2009/09/11 gadget: Number of LUNs=1 lun0: LUN: removable file: (no medium) gadget: Mass Storage Gadget, version: 2009/09/11 gadget: userspace failed to provide iSerialNumber gadget: g_mass_storage ready musb-hdrc musb-hdrc: MUSB HDRC host driver musb-hdrc musb-hdrc: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected mousedev: PS/2 mouse device common for all mice twl_rtc twl_rtc: Power up reset detected. twl_rtc twl_rtc: Enabling TWL-RTC twl_rtc twl_rtc: rtc core: registered twl_rtc as rtc0 cpuidle: using governor ladder cpuidle: using governor menu usb 1-2: new high-speed USB device number 2 using ehci-omap usbcore: registered new interface driver usbhid usbhid: USB HID core driver OMAP3 Beagle/Devkit8000 SoC init soc-audio soc-audio: ASoC machine omap3beagle should use snd_soc_register_card() twl4030-codec twl4030-codec: ASoC: Failed to create Capture debugfs file asoc: twl4030-hifi <-> omap-mcbsp.2 mapping ok oprofile: hardware counters not available oprofile: using timer interrupt. pktgen: Packet Generator for packet performance testing. Version: 2.74 NET: Registered protocol family 15 8021q: 802.1Q VLAN Support v1.8 VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3 ThumbEE CPU extension supported. hub 1-2:1.0: USB hub found sr_init: No PMIC hook to init smartreflex smartreflex smartreflex.0: omap_sr_probe: SmartReflex driver initialized smartreflex smartreflex.1: omap_sr_probe: SmartReflex driver initialized SmartReflex Class3 initialized clock: disabling unused clocks to save power hub 1-2:1.0: 5 ports detected Console: switching to colour frame buffer device 210x65 omapdss DPI: Could not find exact pixel clock. Requested 146262 kHz, got 144000 kHz VDAC: incomplete constraints, leaving on twl_rtc twl_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) ALSA device list: #0: omap3beagle Waiting for root device /dev/mmcblk0p2... mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new high speed SDHC card at address 1234 mmcblk0: mmc0:1234 SA04G 3.63 GiB mmcblk0: p1 p2 EXT3-fs (mmcblk0p2): recovery required on readonly filesystem EXT3-fs (mmcblk0p2): write access will be enabled during recovery usb 1-2.1: new high-speed USB device number 3 using ehci-omap smsc95xx v1.0.4 smsc95xx 1-2.1:1.0: eth0: register 'smsc95xx' at usb-ehci-omap.0-2.1, smsc95xx USB 2.0 Ethernet, 7e:87:52:66:65:ea usb 1-2.2: new high-speed USB device number 4 using ehci-omap hub 1-2.2:1.0: USB hub found hub 1-2.2:1.0: 7 ports detected usb 1-2.2.5: new low-speed USB device number 5 using ehci-omap input: Dell Dell USB Keyboard as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-2/1-2.2/1-2.2.5/1-2.2.5:1.0/input/input0 generic-usb 0003:413C:2003.0001: input: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-ehci-omap.0-2.2.5/input0 usb 1-2.2.6: new low-speed USB device number 6 using ehci-omap input: USB Optical Mouse as /devices/platform/usbhs_omap/ehci-omap.0/usb1/1-2/1-2.2/1-2.2.6/1-2.2.6:1.0/input/input1 generic-usb 0003:0461:4D15.0002: input: USB HID v1.11 Mouse [USB Optical Mouse] on usb-ehci-omap.0-2.2.6/input0 kjournald starting. Commit interval 5 seconds EXT3-fs (mmcblk0p2): recovery complete EXT3-fs (mmcblk0p2): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 179:2. devtmpfs: mounted Freeing init memory: 244K INIT: version 2.88 booting mount: wrong fs type, bad option, bad superblock on tmpfs, missing codepage or helper program, or other error In some cases useful info is found in syslog - try dmesg | tail or so Starting udev udevd[96]: error getting socket: Address family not supported by protocol error initializing udev control socketudevd[96]: error initializing udev control socket error getting socket: Address family not supported by protocol udevadm[97]: error getting socket: Address family not supported by protocol error getting socket: Address family not supported by protocol udevadm[99]: error getting socket: Address family not supported by protocol Starting Bootlog daemon: bootlogd. EXT3-fs (mmcblk0p2): using internal journal ALSA: Restoring mixer settings... Configuring network interfaces... Found hardware: "omap3beagle" "" "" "" "" Hardware is initialized using a generic method ifconfig: socket: Address family not supported by protocol ifconfig: socket: Address family not supported by protocol Starting rpcbind daemon...rpcbind: cannot create socket for local rpcbind: cannot create socket for udp rpcbind: cannot create socket for tcp rpcbind: cannot create socket for udp6 rpcbind: cannot create socket for tcp6 done. Thu Apr 11 17:17:00 UTC 2013 INIT: Entering runlevel: 5 Starting system message bus: Failed to start message bus: Failed to open socket: Address family not supported by protocol Starting Connection Manager Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting advanced power management daemon: apmd. apmd[223]: apmd 3.2.1 interfacing with apm driver 1.13 and APM BIOS 1.2 Starting Distributed Compiler Daemon: distcc/etc/rc5.d/S20distcc: start failed with error code 102 _XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6 _XSERVTransOpen: transport open failed for inet6/beagleboard:0 _XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6 _XSERVTransSocketOpenCOTSServer: Unable to open socket for inet _XSERVTransOpen: transport open failed for inet/beagleboard:0 _XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet _XSERVTransSocketOpenCOTSServer: Unable to open socket for local _XSERVTransOpen: transport open failed for local/beagleboard:0 _XSERVTransMakeAllCOTSServerListeners: failed to open listener for local _XSERVTransSocketOpenCOTSServer: Unable to open socket for unix _XSERVTransOpen: transport open failed for unix/beagleboard:0 _XSERVTransMakeAllCOTSServerListeners: failed to open listener for unix Fatal server error: Cannot establish any listening sockets - Make sure an X server isn't already running (EE) Please consult the The X.Org Foundation support at http://wiki.x.org for help. (EE) Please also check the log file at "/var/log/Xorg.0.log" for additional information. (EE) Server terminated with error (1). Closing log file. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon xinit: giving up xinit: unable to connect to X server: Address family not supported by protocol xinit: server error Timeout reached while wating for return value *[fail]t receive return value from daemon process. Starting Telephony daemon Starting Linux NFC daemon Starting OProfileUI server Starting tcf-agent: ** (oprofile-server:260): ERROR **: Could not open server socket: Address family not supported by protocol OK Stopping Bootlog daemon: bootlogd. Poky 9.0 (Yocto Project 1.4 Reference Distro) 1.4 beagleboard ttyO2 beagleboard login: root root@beagleboard:~# ifconfig ifconfig: error: no inet socket available: Address family not supported by protocol root@beagleboard:~# more /var/log/Xorg.0.log [4195988.202] _XSERVTransSocketOpenCOTSServer: Unable to open socket for inet6 [4195988.203] _XSERVTransOpen: transport open failed for inet6/beagleboard:0 [4195988.203] _XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet6 [4195988.204] _XSERVTransSocketOpenCOTSServer: Unable to open socket for inet [4195988.204] _XSERVTransOpen: transport open failed for inet/beagleboard:0 [4195988.205] _XSERVTransMakeAllCOTSServerListeners: failed to open listener for inet [4195988.205] _XSERVTransSocketOpenCOTSServer: Unable to open socket for local [4195988.205] _XSERVTransOpen: transport open failed for local/beagleboard:0 [4195988.206] _XSERVTransMakeAllCOTSServerListeners: failed to open listener for local [4195988.206] _XSERVTransSocketOpenCOTSServer: Unable to open socket for unix [4195988.206] _XSERVTransOpen: transport open failed for unix/beagleboard:0 [4195988.207] _XSERVTransMakeAllCOTSServerListeners: failed to open listener for unix [4195988.207] Fatal server error: [4195988.208] Cannot establish any listening sockets - Make sure an X server isn 't already running [4195988.208] (EE) Please consult the The X.Org Foundation support at http://wiki.x.org for help. [4195988.209] (EE) Please also check the log file at "/var/log/Xorg.0.log" for a dditional information. [4195988.209] (EE) [4195988.215] Server terminated with error (1). Closing log file. root@beagleboard:~# root@beagleboard:~# date Thu Apr 11 17:25:17 UTC 2013 root@beagleboard:~# uname -a Linux beagleboard 3.4.36-yocto-standard #1 Thu Apr 11 16:25:58 GMT 2013 armv7l GNU/Linux root@beagleboard:~#
The kernel configuration should be fine then. Has anything else changed in the X area ? I have a beagleboard here, but no display, so I can't test this myself.
X failing is just the final error, everything else that touches sockets fails earlier - notice udevd failing too.
Bruce, looking at the startup errors, you'd see problems even just with console startup. It looks like networking support (unix domain sockets?) are missing from the kernel...
My beagle isn't displaying anything but junk to the console. so I need to debug infrastructure before I can see any boot messages at all :(
My serial console is fixed. I'll do a new build of a kernel and see what my bootload looks like.
I've found the missing options. A fix is forthcoming, I'll take care of this after confirming the fsl-mpc NFS root issues.
Patch is in Richard's hands for this issue.
Fix merged to master: http://git.yoctoproject.org/cgit.cgi/poky/commit/?id=c8fa22dd8d5c5173f629961be3ecb0186dd8984f
Verified with dylan branch: 789b2b7e0cca404ff8ba8ed5ba823d215e6ba5b4