Image location: http://autobuilder.yoctoproject.org/pub/nightly/20130411-3/ Git rev: dylan/dab237bc6a7679dfeaa981c14736aedc7b04ecb9 The routerstation and mpc8315e can not boot up via nfs. routerstation boot log: ################# Board: Ubiquiti RouterStation PRO Arch: ar7100pro RAM: 0x80000000-0x88000000, [0x8003bf00-0x87fe1000] available Flash: 0xbf000000-0xc0000000, in 256 blocks of 0x00010000 bytes each == Executing boot script in 10.000 seconds - enter ^C to abort RedBoot> ip_address -l 128.224.178.127 -h 128.224.178.20 IP: 128.224.178.127/255.255.255.0, Gateway: 128.224.162.1 Default server: 128.224.178.20 RedBoot> load -v vlm-boards/19255/kernel Using default protocol (TFTP) Entry point: 0x803a4400, address range: 0x80060000-0x80537c54 RedBoot> exec -c "console=ttyS0,115200 root=/dev/nfs rw nfsroot=128.224.178.20:/export/pxeboot/vlm-boards/19255/rootfs ip=128.224.178.127:128.224.178.20:128.224.178.1:255.255.254.0::eth0:off board=UBNT-RSPRO" Now booting linux kernel: Base address 0x80050000 Entry 0x803a4400 Cmdline : console=ttyS0,115200 root=/dev/nfs rw nfsroot=128.224.178.20:/export/pxeboot/vlm-boards/19255/rootfs ip=128.224.178.127:128.224.178.20:128.224.178.1:255.255.254.0::eth0:off board=UBNT-RSPRO memsize=0x08000000 modetty0=0,n,8,1,hw board=RouterStation PRO ethaddr=00.00.00.00.46.61 Linux version 3.4.36-yocto-standard (pokybuild@ab10.i.yoctoproject.org) (gcc version 4.7.2 (GCC) ) #1 Thu Apr 11 14:59:48 UTC 2013 bootconsole [early0] enabled CPU revision is: 00019374 (MIPS 24Kc) SoC: Atheros AR7161 rev 2 Clocks: CPU:720.000MHz, DDR:360.000MHz, AHB:180.000MHz, Ref:40.000MHz Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node Early memory PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=/dev/nfs rw nfsroot=128.224.178.20:/export/pxeboot/vlm-boards/19255/rootfs ip=128.224.178.127:128.224.178.20:128.224.178.1:255.255.254.0::eth0:off board=UBNT-RSPRO ethaddr=00.00.00.00.46.61 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=0001e202 Readback ErrCtl register=0001e202 Memory: 124364k/131072k available (3399k kernel code, 6708k reserved, 1372k data, 184k init, 0k highmem) SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:48 Console: colour dummy device 80x25 Calibrating delay loop... 477.18 BogoMIPS (lpj=954368) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 devtmpfs: initialized gpiochip_add: registered GPIOs 0 to 15 on device: ath79 MIPS: machine is Ubiquiti RouterStation Pro registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 vgaarb: loadedSCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x10000000-0x16ffffff] pci_bus 0000:00: root bus resource [io 0x0000] Switching to clocksource MIPS squashfs: version 4.0 (2009/01/31) Phillip Lougher jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. ROMFS MTD (C) 2007 Red Hat, Inc. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled loop: module loaded ath79-spi ath79-spi: master is unqueued, this is deprecated ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-platform ehci-platform: Generic Platform EHCI Controller ehci-platform ehci-platform: new USB bus registered, assigned bus number 1 ehci-platform ehci-platform: irq 3, io mem 0x1b000000 ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ohci-platform ohci-platform: Generic Platform OHCI Controller ohci-platform ohci-platform: new USB bus registered, assigned bus number 2 ohci-platform ohci-platform: irq 14, io mem 0x1c000000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i8042: i8042 controller selftest timeout Trying to free nonexistent resource <0000000000000060-000000000000006f> mousedev: PS/2 mouse device common for all mice watchdog: Software Watchdog: cannot register miscdev on minor=130 (err=-16) watchdog: error registering /dev/watchdog (err=-16) md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: using mips/24K performance monitoring. md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. VFS: Cannot open root device "nfs" or unknown-block(0,255): error -6 Please append a correct "root=" boot option; here are the available partitions: VFS: Unable to mount root fs on unknown-block(0,255) User configuration error - no valid root filesystem found Kernel panic - not syncing: Invalid configuration from end user prevents continuing ################### mpc8315e boot log: ################## U-Boot 2012.04.01 (Jun 29 2012 - 13:48:03)MPC83XX Reset Status: Software Hard, External/Internal Soft, External/Internal Hard CPU: e300c3, MPC8315E, Rev: 1.2 at 400 MHz, CSB: 133.333 MHz Board: Freescale MPC8315ERDB Rev 1.0 I2C: ready DRAM: 128 MiB (DDR2, 32-bit, ECC off, 266.667 MHz) Flash: 8 MiB NAND: 32 MiB PCIE0: No link PCIE1: No link In: serial Out: serial Err: serial Net: eTSEC0, eTSEC1 Hit any key to stop autoboot: 0 Speed: 100, full duplex Using eTSEC0 device TFTP from server 128.224.165.20; our IP address is 128.224.178.141 Filename 'vlm-boards/17652/kernel'. Load address: 0x1000000 Loading: ################################################################# ################################################################# ############################################ done Bytes transferred = 2552265 (26f1c9 hex) Speed: 100, full duplex Using eTSEC0 device TFTP from server 128.224.165.20; our IP address is 128.224.178.141 Filename 'vlm-boards/17652/dtb'. Load address: 0xa00000 Loading: ## done Bytes transferred = 21042 (5232 hex) ## Booting kernel from Legacy Image at 01000000 ... Image Name: Linux-3.4.36-yocto-standard Created: 2013-04-11 14:56:26 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2552201 Bytes = 2.4 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at 00a00000 Booting using the fdt blob at 0x00a00000 Uncompressing Kernel Image ... OK Loading Device Tree to 07f0f000, end 07f17231 ... OK NOTICE: No or unknown board_type hwconfig specified. Assuming board with TSEC1. Using MPC831x RDB machine description Linux version 3.4.36-yocto-standard (pokybuild@autobuilder04) (gcc version 4.7.2 (GCC) ) #1 Thu Apr 11 14:56:24 UTC 2013 bootconsole [udbg0] enabled setup_arch: bootmem mpc831x_rdb_setup_arch() Found FSL PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 PCI host bridge /pci@e0008500 (primary) ranges: MEM 0x0000000090000000..0x000000009fffffff -> 0x0000000090000000 MEM 0x0000000080000000..0x000000008fffffff -> 0x0000000080000000 Prefetch IO 0x00000000e0300000..0x00000000e03fffff -> 0x0000000000000000 No pci config register base in dev tree, using default Found FSL PCI host bridge at 0x00000000e0009000. Firmware bus number: 0->255 PCI host bridge /pcie@e0009000 ranges: MEM 0x00000000a0000000..0x00000000afffffff -> 0x00000000a0000000 IO 0x00000000b1000000..0x00000000b17fffff -> 0x0000000000000000 No pci config register base in dev tree, using default Found FSL PCI host bridge at 0x00000000e000a000. Firmware bus number: 0->255 PCI host bridge /pcie@e000a000 ranges: MEM 0x00000000c0000000..0x00000000cfffffff -> 0x00000000c0000000 IO 0x00000000d1000000..0x00000000d17fffff -> 0x0000000000000000 arch: exit Zone PFN ranges: DMA 0x00000000 -> 0x00008000 Normal empty Movable zone start PFN for each node Early memory PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: root=/dev/nfs rw nfsroot=128.224.165.20:/export/pxeboot/vlm-boards/17652/rootfs/ ip=128.224.178.141:128.224.165.20:128.224.178.1:::eth0:off console=ttyS0,115200 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 124556k/131072k available (4924k kernel code, 6516k reserved, 176k data, 175k bss, 152k init) Kernel virtual memory layout: * 0xfffdf000..0xfffff000 : fixmap * 0xfcef7000..0xfe000000 : early ioremap * 0xc9000000..0xfcef7000 : vmalloc & ioremap SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:512 nr_irqs:512 16 IPIC (128 IRQ sources) at c9000700 clocksource: timebase mult[1e000005] shift[24] registered Console: colour dummy device 80x25 pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 512 devtmpfs: initialized PCI: Probing PCI hardware PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] pci_bus 0000:00: root bus resource [mem 0x90000000-0x9fffffff] pci_bus 0000:00: root bus resource [mem 0x80000000-0x8fffffff pref] PCI host bridge to bus 0001:01 pci_bus 0001:01: root bus resource [io 0xff7fe000-0xffffdfff] (bus address [0x0000-0x7fffff]) pci_bus 0001:01: root bus resource [mem 0xa0000000-0xafffffff] PCI host bridge to bus 0002:02 pci_bus 0002:02: root bus resource [io 0xfeffc000-0xff7fbfff] (bus address [0x0000-0x7fffff]) pci_bus 0002:02: root bus resource [mem 0xc0000000-0xcfffffff] bio: create slab <bio-0> at 0 Freescale Elo / Elo Plus DMA driver vgaarb: loaded SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource timebase fsl-elo-dma e00082a8.dma: #0 (fsl,elo-dma-channel), irq 71 fsl-elo-dma e00082a8.dma: #1 (fsl,elo-dma-channel), irq 71 fsl-elo-dma e00082a8.dma: #2 (fsl,elo-dma-channel), irq 71 fsl-elo-dma e00082a8.dma: #3 (fsl,elo-dma-channel), irq 71 ROMFS MTD (C) 2007 Red Hat, Inc. Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 16) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 17) is a 16550A loop: module loaded fsl-sata e0018000.sata: Sata FSL Platform/CSB Driver init scsi0 : sata_fsl ata1: SATA max UDMA/133 irq 44 fsl-sata e0019000.sata: Sata FSL Platform/CSB Driver init scsi1 : sata_fsl ata2: SATA max UDMA/133 irq 45 fe000000.flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001001 Amd/Fujitsu Extended Query Table at 0x0040 Amd/Fujitsu Extended Query version 1.3. fe000000.flash: Swapping erase regions for top-boot CFI table. number of CFI chips: 1 fsl_spi e0007000.spi: master is unqueued, this is deprecated fsl_spi e0007000.spi: at 0xc9020000 (irq = 19), CPU mode ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver /immr@e0000000/usb@23000: Invalid 'dr_mode' property, fallback to host mode fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 38, io mem 0xe0023000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mousedev: PS/2 mouse device common for all mice i2c /dev entries driver mpc-i2c e0003000.i2c: timeout 1000000 us at24 0-0050: 32768 byte 24c256 EEPROM, writable, 1 bytes/write rtc-ds1307 0-0068: rtc core: registered ds1339 as rtc0 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com talitos e0030000.crypto: hwrng talitos e0030000.crypto: fsl,sec3.3 algorithms registered in /proc/crypto usbcore: registered new interface driver usbhid usbhid: USB HID core driver oprofile: using timer interrupt. rtc-ds1307 0-0068: setting system clock to 2013-04-12 07:09:55 UTC (1365750595) usb 1-1: new high-speed USB device number 2 using fsl-ehci hub 1-1:1.0: USB hub found ata2: No Device OR PHYRDY change,Hstatus = 0xa0000000 ata2: SATA link down (SStatus 0 SControl 300) ata1: Signature Update detected @ 504 msecs hub 1-1:1.0: 4 ports detected ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300) ata1.00: ATA-8: WDC WD1600AAJS-22L7A0, 01.03E01, max UDMA/133 ata1.00: 312581808 sectors, multi 0: LBA48 NCQ (depth 16/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD1600AAJS-2 01.0 PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 312581808 512-byte logical blocks: (160 GB/149 GiB) sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 > sd 0:0:0:0: [sda] Attached SCSI disk md: Waiting for all devices to be available before autodetect md: If you don't use raid, use raid=noautodetect md: Autodetecting RAID arrays. md: Scanned 0 and added 0 devices. md: autorun ... md: ... autorun DONE. VFS: Cannot open root device "nfs" or unknown-block(0,255): error -6 Please append a correct "root=" boot option; here are the available partitions: 1f00 8192 mtdblock0 (driver?) 0800 156290904 sda driver: sd 0801 41943040 sda1 00000000-0000-0000-0000-000000000000 0802 41943040 sda2 00000000-0000-0000-0000-000000000000 0803 41943040 sda3 00000000-0000-0000-0000-000000000000 0804 1 sda4 00000000-0000-0000-0000-000000000000 0805 30459736 sda5 00000000-0000-0000-0000-000000000000 VFS: Unable to mount root fs on unknown-block(0,255) User configuration error - no valid root filesystem found Kernel panic - not syncing: Invalid configuration from end user prevents continuing Call Trace: [c7829e70] [c0007ad4] show_stack+0x48/0x150 (unreliable) [c7829eb0] [c034b028] panic+0xc0/0x1f8 [c7829f00] [c04a9ed4] mount_block_root+0x27c/0x2a0 [c7829f50] [c04aa0bc] prepare_namespace+0x15c/0x1a4 [c7829f60] [c04a9b10] kernel_init+0x1dc/0x1e0 [c7829ff0] [c000d548] kernel_thread+0x4c/0x68 Rebooting in 180 seconds.. ######################
Can someone grep the kernel config for NFS root options ? Mine are all present and accounted for: > grep NFS 3.8.4+gitAUTOINC+27b63fdbd25ad1a37bacc05f49a205c150d21779_11998bd1f44b21cd0b8c0ca11cbd36865f14bfdc-r4.0/linux-routerstationpro-standard-build/.config CONFIG_NFS_FS=y CONFIG_NFS_V2=y CONFIG_NFS_DEF_FILE_IO_SIZE=4096 CONFIG_NFS_V3=y # CONFIG_NFS_V3_ACL is not set CONFIG_NFS_V4=y # CONFIG_NFS_SWAP is not set # CONFIG_NFS_V4_1 is not set CONFIG_ROOT_NFS=y # CONFIG_NFS_USE_LEGACY_DNS is not set CONFIG_NFS_USE_KERNEL_DNS=y # CONFIG_NFSD is not set CONFIG_NFS_COMMON=y
I just built and booted this: root@mpc8315e-rdb:~# uname -a Linux mpc8315e-rdb 3.4.36-yocto-standard #1 PREEMPT Fri Apr 12 10:28:27 EDT 2013 ppc GNU/Linux root@mpc8315e-rdb:~# cat /proc/cmdline root=/dev/nfs rw nfsroot=128.224.146.167:/nfsroot/mpc8315erdb ip=128.224.146.168:128.224.146.167:128.224.146.1:255.255.254.0::eth0:off console=ttyS0,115200 With a fix I'm doing for the beagleboard, so at the minimum, this issue will be resolved with that bug. Patches are forthcoming.
root@routerstationpro:~# uname -a Linux routerstationpro 3.4.36-yocto-standard #1 PREEMPT Fri Apr 12 11:05:35 EDT 2013 mips GNU/Linux root@routerstationpro:~# cat /proc/cmdline console=ttyS0,115200 root=/dev/nfs rw nfsroot=128.224.146.167:/nfsroot/rsp ip=128.224.146.168:128.224.146.167:128.224.146.1:255.255.254.0::eth0:off ethaddr=00.15.6d.c5.c3.ad board=UBNT-RSPRO
Patch sent to Richard for this issue.
Merged into master: http://git.yoctoproject.org/cgit.cgi/poky/commit/?id=c8fa22dd8d5c5173f629961be3ecb0186dd8984f
Verified with dylan branch: 789b2b7e0cca404ff8ba8ed5ba823d215e6ba5b4