Hi, After the system boots, there is NO PROMPT on the monitor, but the serial port does show a prompt. A Denzil sato BSP does boot properly and the monitor works ok for that version. A Denzil based sato "no pvr" build is also working with the board and monitor. note: The Sato image does not launch X-windows and details are shown on bug report 3607. hci_hcd 0000:00:1d.2: irq 18, io base 0x0000f060 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000f040 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mousedev: PS/2 mouse device common for all mice rtc_cmos 00:06: RTC can wake from S4 rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 md: raid10 personality registered for level 10 md: multipath personality registered for level -4 md: faulty personality registered for level -5 device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com ata1: SATA link down (SStatus 0 SControl 300) cpuidle: using governor ladder cpuidle: using governor menu sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman EFI Variables Facility v0.08 2004-May-17 usbcore: registered new interface driver usbhid usbhid: USB HID core driver HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 hda_codec: ALC662 rev1: BIOS auto-probing. HDMI status: Pin=3 Presence_Detect=0 ELD_Valid=0 ALSA device list: #0: HDA Intel at 0xdff00000 irq 22 oprofile: using NMI interrupt. TCP cubic registered NET: Registered protocol family 17 Registering the dns_resolver key type Using IPI No-Shortcut mode registered taskstats version 1 rtc_cmos 00:06: setting system clock to 2012-12-17 19:05:36 UTC (1355771136) pvrsrvkm 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [TTM] Zone kernel: Available graphics memory: 437318 kiB. [TTM] Zone highmem: Available graphics memory: 1025654 kiB. [TTM] Initializing pool allocator. [drm:psb_driver_load] *ERROR* Enable MSI failed! [drm] Supports vblank timestamp caching Rev 1 (10.10.2010). [drm] No driver support for vblank timestamp query. input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/ input3 ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no) usb 1-7: new high speed USB device number 3 using ehci_hcd Overlay GTT address is 7c0000 ata2: SATA link down (SStatus 0 SControl 300) scsi4 : usb-storage 1-7:1.0 usb 2-1: new low speed USB device number 2 using uhci_hcd input: Microsoft Basic Optical Mouse as /devices/pci0000:00/0000:00:1d.0/usb2/2- 1/2-1:1.0/input/input4 generic-usb 0003:045E:0084.0001: input: USB HID v1.10 Mouse [Microsoft Basic Opt ical Mouse] on usb-0000:00:1d.0-1/input0 fbcon: psbfb (fb0) is primary device scsi 4:0:0:0: Direct-Access USB Flash Memory 1.00 PQ: 0 ANSI: 2 sd 4:0:0:0: Attached scsi generic sg0 type 0 sd 4:0:0:0: [sda] 1001472 512-byte logical blocks: (512 MB/489 MiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] No Caching mode page present sd 4:0:0:0: [sda] Assuming drive cache: write through sd 4:0:0:0: [sda] No Caching mode page present sd 4:0:0:0: [sda] Assuming drive cache: write through sda: sd 4:0:0:0: [sda] No Caching mode page present sd 4:0:0:0: [sda] Assuming drive cache: write through sd 4:0:0:0: [sda] Attached SCSI removable disk Console: switching to colour frame buffer device 128x48 fb0: psbfb frame buffer device drm: registered panic notifier Cedartrail: apply sample cache workaround Device ID: 2 [drm] Initialized pvrsrvkm 8.1.0 2009-03-10 for 0000:00:02.0 on minor 0 Freeing unused kernel memory: 500k freed udev[66]: starting version 164 EXT3-fs (loop0): warning: feature flags set on rev 0 fs, running e2fsck is recom mended EXT3-fs: barriers not enabled kjournald starting. Commit interval 5 seconds EXT3-fs (loop0): warning: updating to rev 1 because of new feature flag, running e2fsck is recommended EXT3-fs (loop0): using internal journal EXT3-fs (loop0): mounted filesystem with ordered data mode udev[515]: starting version 164 r8169 0000:02:00.0: eth0: link down Poky 8.0 (Yocto Project 1.3 Reference Distro) 1.3 cedartrail ttyS0 cedartrail login:
denzil:cedartrail: works denzil:cedartrail-nopvr: works danny:cedartrail: doesn't work danny:cedartrail-nopvr: ? From 3607 we understand that the Sato image does not start X. In this report you are saying that... you don't get anything on the monitor? Or you get kernel/boot messages but no login prompt? Kishore, can you please ACCEPT and help jsshetler out?
Hi Rahul, Can you take a look at this? From Bug 3607, I had pointed Joy Shetler to first try out the binaries we have posted on Yocto project website. As you might be knowing there are some Cedartrail SKUs on which X does not come up. Thanks Kishore.
jsshetler, which board are you using ? Also how is this bug different from #3607 ? Can you also pl post the contents of /var/log/Xorg.0.log
Sorry, I had one piece of info wrong on the description. This system did not work with ANY of the sato versions - Denzil or Danny. It does work with some of the minimal versions. Some of the boot operations are recorded on the monitor, then the monitor goes blank for the sato versions. We are able to retrieve some information by using the serial port. It looks like there might be a patch working for the other system. If this is SKU related, we will be using a B3 stepping instead of a B2 stepping for future systems, due out in a couple of weeks.
The updated Danny BSP binary w/ patch for bug 3607 DID NOT launch X-windows on the CDT CRB (We have not tried other Danny sato based builds w/ patch on the CRB yet). There is a log-in prompt on the screen, but X-windows did NOT launch. BTW, the sato based Denzil “no pvr” build did launch X-windows properly on the CDT CRB, but none of the prior BSP sato distributions launch X-windows on that platform. So far, this is the ONLY sato based build or BSP binary that launchs X-windows on this particular platform. So, we would like some more information on what the 3607 patch actually changes. I should have some more detailed questions soon. We will also be collecting more info and files from the CRB next week.
I have updated #3607 with the explaination for the kernel command line fix.
We are now using the new DE2i-150 board and have a Danny sato Yocto version booting on all these boards. Assume that errors on this board were sku related. Thanks everyone!